Air Trigger for Airsoft · User Manual v1.0
TRUEDYNAMIC · BY TRUECLAYS

Air Trigger for Airsoft

User manual: how it works, fitting the mount and the hose, the battery, changing the balloon, and daily care

Revision v1.0 · 2026-11-15

Contents

  1. 1Welcome
  2. 2Know your unit
  3. 3The mounts
  4. 4The hose
  5. 5Battery
  6. 6Changing the balloon
  7. 7Aiming and first shots
  8. 8Daily use, storage and care
  9. 9Troubleshooting, FAQ and support

1 Welcome

The Air Trigger turns your own airsoft gun into a laser trainer for TrueDynamic. The unit clamps to a rail or to the barrel, and a soft hose goes from the unit into the muzzle. When you fire, the puff of air from the gun blows up a small balloon inside the unit. The balloon pushes a switch, and the unit fires a short laser pulse. TrueDynamic sees the dot on the screen and scores the shot.

Nothing is changed inside the gun. Take the hose out and the unit off, and the gun is an ordinary airsoft gun again. Every shot gives one pulse, so it works in semi and in full auto.

Never load BBs

The unit works on air only. Before you fit the hose, take the magazine out and fire a few shots in a safe direction to make sure no BB is left in the gun. A BB fired into the hose can damage the balloon and the unit. Never point the laser at anyone's eyes.

In the box

  • Air Trigger unit with balloon fitted
  • Picatinny mount (fitted)
  • Barrel mount for barrels 10–20 mm
  • Silicone hose, 6 mm outside / 4 mm inside
  • Spare balloons
  • 4LR44 6 V battery (fitted)
  • Hex keys, 2 mm and 2.5 mm

What you need

  • An airsoft gun: electric, gas or spring
  • A Picatinny rail, or a round barrel 10–20 mm
  • A TrueDynamic system, installed and calibrated

2 Know your unit

The parts you will touch, and the ones that are set at the factory. Sides are named as seen from behind the gun, with the lid up.

PartWhat it does
Hose connectorThe small spout on the front. The hose pushes onto it.
Balloon plugCarries the hose connector and the balloon. Pulls out of the front to change the balloon.
Plug thumb screwOn the left side, near the front. Holds the balloon plug in. Turn it by hand.
Vent holesThe row of small holes on the left side. They let the air out after each shot. Keep them open.
LaserIn the front face, at the top, pointing along the barrel.
LidOn top, with four screws. The battery is under it.
MountBolted under the unit with four screws. Picatinny or barrel, see section 3.
Factory-set screws

The larger screw in the middle of the left side holds the piston inside the unit. The small screw near the top front of the left side holds the laser. Both are set at the factory. Leave them alone.

How it works

At rest: the balloon is slack and the switch (black) is open.
Shot: the balloon fills the chamber and pushes the piston onto the switch.
  1. The shot blows air down the barrel, into the hose and through the plug into the balloon.
  2. The balloon swells and pushes the piston back. The piston's plastic tip presses the switch.
  3. The switch fires one short laser pulse.
  4. The air leaves through the vent holes, the balloon goes slack, and the unit is ready for the next shot.

Specifications

ItemValue
Size (unit)37 × 28 × 55 mm (width × height × length)
Height with mount39 mm with the Picatinny mount
FitsPicatinny rails, or round barrels 10–20 mm with the barrel mount
HoseSilicone, 6 mm outside, 4 mm inside
Battery4LR44, 6 V
LaserOne short pulse per shot. It is aimed in TrueDynamic, so it has no mechanical adjustment.

3 The mounts

There are two mounts: one for a Picatinny rail and one for a round barrel. Use the one that suits your gun. Neither has to be very tight; there is hardly any recoil.

Picatinny mount

  1. Loosen the jaw screw on the left side with the 2.5 mm hex key until the jaw opens.
  2. Put the mount on the rail with the hose connector pointing to the muzzle.
  3. Slide the unit forwards or backwards to where you want it. There is no cross-bolt, so any position along the rail works.
  4. Tighten the jaw screw until the unit no longer moves. Firm is enough.

Barrel mount

  1. Loosen the jaw screw on the left side with the 2.5 mm hex key. The jaw slides out on its own guide.
  2. Rest the fixed V of the mount on the barrel, with the hose connector pointing to the muzzle.
  3. Slide the jaw in against the barrel and tighten the screw until the unit no longer turns.

The barrel mount fits barrels from 10 to 20 mm. The nut is held in the mount, so you only need one key.

Changing the mount

  1. Take the unit off the gun.
  2. Turn it upside down and remove the four countersunk screws in the bottom of the mount with the 2 mm hex key.
  3. Lift the mount off and put the other one on, the same way round.
  4. Fit the four screws and tighten them gently. They go into threaded inserts, so do not overtighten.
The unit can sit on top of the gun or under it. Upside down works just as well.

4 The hose

The hose carries the air from the barrel to the balloon. It must sit tight at both ends, or the air escapes before it reaches the balloon.

  1. Make sure the gun is empty: magazine out, no BB left in the gun (section 1).
  2. Push one end of the hose onto the hose connector on the front of the unit, all the way over the ridges.
  3. Lead the hose to the muzzle and push the other end into the barrel until it sits firmly.
  4. Fire one shot and check that the laser fires (section 7).
Keep the hose out of the laser beam

The laser shines forwards from the top of the front face. Route the hose so that it does not cross in front of the laser.

Taking the hose out

Pull the hose out of the barrel by hand. The gun is then back to normal airsoft use. Fit the hose again the same way next time.

5 Battery

The unit runs on one 4LR44 6 V battery, under the lid.

The battery lies along the right side. The front contact is a flat plate with a button; the rear contact is a spring.

Changing the battery

  1. Take the unit off the gun.
  2. Remove the four lid screws with the 2 mm hex key and lift off the lid.
  3. Take out the old battery. Put in the new one with the + end against the button contact at the front and the − end against the spring at the rear.
  4. Put the lid back and tighten the four screws gently. Do not pinch any wires under the lid.
The battery is only used during a shot

The switch is only pressed while the balloon is blown up, so the unit uses no power while it waits. There is no on/off switch, and none is needed.

6 Changing the balloon

The balloon is a small water balloon. It lasts a long time, but if the laser stops firing it is the first thing to check.

Thumb screw loosened, balloon plug pulled out.
Balloon pulled over the nose of the plug, up to the slope.
  1. Pull the hose off the hose connector.
  2. Turn the plug thumb screw out a few turns, until the plug is free. It does not have to come out.
  3. Pull the plug straight out of the front by the hose connector. The piston stays inside.
  4. Roll the old balloon off the nose of the plug.
  5. Stretch the neck of a new balloon over the nose, past the small ridge and up to the slope. Pull it straight so it is not twisted.
  6. Push the plug back in until its flange is flat against the front face. The O-ring makes it a little stiff at the end.
  7. Turn the thumb screw in by hand until it is firm, and push the hose back on.
Don't loosen the piston screw

The piston stays in the unit when the plug is out. It is held by the larger screw in the middle of the left side. Leave that screw alone, or the piston can fall out and turn.

Which balloons?

  • Small latex water balloons, the kind sold in packs of hundreds. Use the spare balloons in the box as a guide.
  • Keep spare balloons in a closed bag, away from light and heat. Old latex goes brittle.
Hand tight is enough

The thumb screw only stops the plug from being pushed out. Turn it by hand; never use pliers.

7 Aiming and first shots

The laser should hit where the gun points. This is done in TrueDynamic, not on the unit.

  1. Fit the unit and the hose (sections 3 and 4). No BBs in the gun.
  2. Start TrueDynamic and open a stage or the calibration, so you can see when a shot is detected.
  3. Fire one shot. The laser should fire once, and TrueDynamic should show the hit.
  4. Calibrate the firearm in TrueDynamic, as described in the TrueDynamic User Manual, section 3.
  5. Try a short burst if your gun has full auto. Every shot should show as a hit.
Calibrate again after moving the unit

The laser has no mechanical adjustment. If you take the unit off, change the mount or move it along the rail, calibrate the firearm again.

Left side: plug thumb screw at the front, then the vent holes, then the piston screw (factory set).

8 Daily use, storage and care

Every session

  • Gun empty: magazine out, no BBs in the gun, eye protection as usual for airsoft.
  • Unit fitted, mount screw firm.
  • Hose tight on the connector and in the barrel, and clear of the laser.
  • One test shot: the laser fires and TrueDynamic shows the hit.

Storage and transport

  • Take the hose out of the barrel when you are done.
  • For long storage, take the battery out.
  • Keep the unit dry and away from heat. Don't leave it in a car in the sun; heat ages the balloon.

Care

  • Wipe the unit with a dry cloth. Do not use solvents or silicone oil on it; oil damages the balloon.
  • Keep the laser window clean. Use a cotton bud if it gets dusty.
  • Keep the vent holes open.
  • Replace the hose if it gets loose on the connector or splits at the end.

9 Troubleshooting, FAQ and support

ProblemWhat to do
No shot when I fireCheck that the hose is tight at both ends. Check the battery (section 5). Change the balloon (section 6).
Some shots are missingThe hose leaks at the muzzle or at the connector. Push it in further, or cut a few millimetres off the end.
The laser stays onThe piston is held back. Take the plug out and check that the balloon is not twisted or folded behind the plug.
Hits land beside the aim pointCalibrate the firearm again in TrueDynamic, especially after the unit has been moved.
The plug pushes outTighten the plug thumb screw by hand.
The unit moves on the gunTighten the jaw screw of the mount (section 3).

FAQ

Does it change my gun?No. Nothing goes inside the gun except the end of the hose, and the mount only clamps on.
Does it work in full auto?Yes. Every shot gives one laser pulse.
Which guns does it fit?Electric, gas and spring airsoft guns with a Picatinny rail or a round barrel of 10–20 mm.
Can I shoot BBs with it fitted?No. Take the hose out and the unit off before you use the gun with BBs.

Get in touch

Supportsupport@trueclays.com
Salessales@trueclays.com
Product pagetrueclays.com/truedynamic
VideosSearch for TrueClays on YouTube
Instagram@trueclays

Train often, shoot straight, and thank you for choosing TrueDynamic.

The pictures are renders of the design; the unit you receive may look slightly different.

TrueDynamic - AirSoftSolution | TrueClays