Laser Trigger for Glock · User Manual v1.0
TRUEDYNAMIC · BY TRUECLAYS

Laser Trigger for Glock

User manual: fitting the unit, the safety plug, the battery, setting the rod and the trip point, and daily care

Revision v1.0 · 2026-11-15

Contents

  1. 1Welcome
  2. 2Know your unit
  3. 3The safety plug
  4. 4Battery
  5. 5Fitting and removing
  6. 6Setting the rod
  7. 7Setting the trip point
  8. 8Daily use, storage and care
  9. 9Troubleshooting, FAQ and support

1 Welcome

The Laser Trigger turns your own Glock into a dry-fire trainer for TrueDynamic. The unit clamps under the front rail. A thin rod rests against the front of the trigger. When you press the trigger, the rod follows it back, and at the break a switch fires a short laser pulse. TrueDynamic sees the dot on the screen and scores the shot.

There is nothing to fit inside the pistol and no tools are needed to put it on or take it off. Each laser pulse is one shot: holding the trigger back does not keep the laser on.

Dry fire only

Before fitting the unit, remove the magazine, lock the slide back and check that the chamber is empty. Keep all live ammunition out of the training room. Never fire live rounds with the unit fitted.

In the box

  • Laser trigger unit with rod, fitted
  • Safety plug with "Remove before shooting" tag (fitted)
  • 4LR44 6 V battery (fitted)
  • 1.5 mm hex key, for the rod clamp and the trip screw

What you need

  • A Glock pistol with an accessory rail
  • A TrueDynamic system, installed and calibrated
  • A small screwdriver, only to change the battery

2 Know your unit

The parts you will touch, and the ones that are set at the factory.

PartWhat it does
Fixed hook (left)Hooks over the left side of the rail.
Jaw and thumb screw (right)The hinged jaw closes on the right side of the rail. Turn the thumb screw by hand to clamp or release it.
RodRuns back to the trigger and rests against its front face.
CarriageSlides inside the housing with the rod. A spring pushes it back, so the rod always follows the trigger.
Rod clamp screwHolds the rod in the carriage. Reached through the slot in the left side.
Trip screwSets where in the trigger travel the switch fires. Reached through the small hole in the front face.
LaserIn the front of the housing, pointing along the barrel.
Battery boxUnder the housing, closed by a lid with four screws.
Safety plugHolds the carriage forward in storage, so the battery is not drained. See section 3.
Factory-set screws

The two screws under the laser, the spring screw in the front face and the hinge-pin screw on the right are set at the factory. Leave them alone.

The unit sits under the rail, in front of the trigger guard. The rod runs back through the trigger guard to the trigger.

Specifications

ItemValue
FitsGlock pistols with an accessory rail
Housing length58.6 mm
Lowest point36.7 mm below the rail
Battery4LR44, 6 V
SwitchMicroswitch, fires near the end of the trigger travel
LaserOne short pulse per shot. It is aimed in TrueDynamic, so it has no mechanical adjustment.

3 The safety plug

The unit is shipped with the safety plug fitted. Remove it before shooting, and fit it again for storage and transport.

The plug is a small square pin with a plate and a ring. It goes into the rear end of the slot in the left side of the housing, and the "Remove before shooting" tag hangs from the ring.

Why it matters: off the pistol, the spring pushes the carriage all the way back and holds the switch closed. That keeps the electronics on and drains the battery. With the plug fitted, the carriage stops before the switch.

Nothing clicks or snaps. The spring presses the carriage against the pin, and that holds the plug in place.

Removing the plug

  1. With the unit on the pistol, rack the slide so the trigger is forward. The trigger now holds the rod and the carriage forward.
  2. Pull the plug straight out by the ring. If the carriage is pressing on it, push the trigger gently forward with a finger while you pull.
  3. Keep the plug with the pistol case.

Fitting the plug

  1. On the pistol: rack the slide so the trigger is forward. Off the pistol: push the rod forward by hand to move the carriage forward.
  2. Push the plug straight in at the rear end of the slot, ring pointing out, until the plate lies flat on the housing.
  3. Let go of the rod. The carriage moves back against the pin and holds it.
Remove before shooting

With the plug fitted, the switch cannot fire. If nothing happens when you press the trigger, check the plug first.

The slot also gives access to the rod clamp

The rod clamp screw sits in the front part of the same slot. You can reach it with the plug fitted.

4 Battery

The unit runs on one 4LR44 6 V battery, in the box under the housing.

Changing the battery

  1. Take the unit off the pistol (section 5) and fit the safety plug.
  2. Turn the unit upside down and remove the four lid screws. Lift off the lid.
  3. Take out the old battery. Put in the new one with the + end against the button contact at the front and the − end against the spring at the rear.
  4. Put the lid back and tighten the four screws gently. They go into plastic, so do not overtighten.
The battery is only used while the switch is closed

The electronics are off until the trigger reaches the trip point. A battery lasts a long time as long as the trigger is not left at the rear. See section 8.

5 Fitting and removing

The unit clamps under the rail. The rod stays set, so it goes back to the same place every time.

Fitting the unit

  1. Make the pistol safe: magazine out, chamber empty.
  2. Turn the thumb screw out until the jaw swings open.
  3. Hold the unit under the rail, with the rod pointing back to the trigger guard. Hook the fixed hook over the left side of the rail and slide the rod in through the trigger guard.
  4. Lift the unit up against the rail, then move it right so the hook seats.
  5. Close the jaw and turn the thumb screw in by hand until it is firm.

Removing the unit

  1. Fit the safety plug if you are storing the unit (section 3).
  2. Turn the thumb screw out until the jaw swings open.
  3. Move the unit about 3 mm to the left, lower it about 5 mm, and pull it out to the left, bringing the rod out of the trigger guard.
Hand tight is enough

Turn the thumb screw by hand only. Too much force can crack the jaw.

6 Setting the rod

Do this once for your pistol, or after you change pistols. The rod must just touch the front of the trigger when the trigger is forward.

  1. Fit the unit (section 5) and rack the slide so the trigger is forward.
  2. Put the 1.5 mm hex key through the slot in the left side, into the rod clamp screw. Loosen it about half a turn.
  3. Slide the rod until its tip just touches the front of the trigger, without pushing it.
  4. Tighten the clamp screw gently.
  5. Press the trigger slowly and let it go. The rod must follow the trigger all the way and come back with it.
Don't back the clamp screw out too far

The screw only needs half a turn to free the rod. It backs out into the slot, and after about 3 turns it reaches the outside of the housing.

After setting the rod, set the trip point (section 7).

7 Setting the trip point

The laser should fire exactly when the pistol would fire: at the break, in the last millimetre of trigger travel.

  1. Start TrueDynamic and open a stage or the calibration, so you can see when a shot is detected.
  2. Remove the safety plug and rack the slide.
  3. Press the trigger very slowly and watch for the shot. Then rack the slide again.
  4. Adjust the trip screw with the 1.5 mm hex key, through the small hole in the front face, a quarter turn at a time:
    • Shot comes too early (before the break): turn it counter-clockwise.
    • Shot comes too late or not at all: turn it clockwise.
  5. Repeat until the shot comes with the break, every time.
Aiming the laser

The laser has no mechanical adjustment. Calibrate the firearm in TrueDynamic, as described in the TrueDynamic User Manual, section 3. Calibrate again after you take the unit off and put it back.

8 Daily use, storage and care

Every session

  • Pistol safe: magazine out, chamber empty, no live ammunition in the room.
  • Unit fitted, thumb screw hand tight.
  • Safety plug removed.
  • Rack the slide before every shot. A Glock trigger stays at the rear after dry fire until you rack the slide.
Don't leave the trigger at the rear

While the trigger is at the rear, the switch stays closed and the battery runs down. After the last shot, rack the slide, or take the unit off and fit the safety plug.

Storage and transport

  • Fit the safety plug whenever the unit is off the pistol.
  • For long storage, take the battery out.
  • Keep the unit dry and away from heat. Don't leave it in a car in the sun.

Care

  • Wipe the unit with a dry cloth. Do not use solvents or gun oil on it.
  • Keep the laser window clean. Use a cotton bud if it gets dusty.
  • Check from time to time that the rod still touches the trigger (section 6).

9 Troubleshooting, FAQ and support

ProblemWhat to do
No shot when I press the triggerRemove the safety plug. Rack the slide. Check the battery. Turn the trip screw clockwise a quarter turn.
Shot comes before the breakTurn the trip screw counter-clockwise a quarter turn (section 7).
Two shots, or a shot when I let goThe rod is not touching the trigger, or the unit is loose. Set the rod again (section 6) and tighten the thumb screw.
Hits land beside the aim pointCalibrate the firearm again in TrueDynamic, especially after the unit has been off the pistol.
Battery runs down fastThe trigger was left at the rear, or the unit was stored without the safety plug. See section 8.
The plug is hard to pull outThe carriage is pressing on it. Push the trigger or the rod forward a little while you pull.

FAQ

Do I need tools to fit it?No. The thumb screw turns by hand. The hex key is only for setting the rod and the trip point.
Does it change my pistol?No. Nothing goes inside the pistol, and the unit only touches the rail and the front of the trigger.
Can I use it with a weapon light or holster?No. The unit uses the rail, so take off other rail accessories first.
Will it fit other pistols?This version is made for Glock rails and trigger guards.

Get in touch

Supportsupport@trueclays.com
Salessales@trueclays.com
Product pagetrueclays.com/truedynamic
VideosSearch for TrueClays on YouTube
Instagram@trueclays

Train often, shoot straight, and thank you for choosing TrueDynamic.

Glock is a registered trademark of GLOCK, Inc. This product is made by TrueClays and is not affiliated with or endorsed by GLOCK, Inc. The pictures are renders of the design; the unit you receive may look slightly different.

TrueDynamic - Gun Laser | TrueClays